• Mixing Ratio
• Part A : Part B = 1 : 2.5 (by weight)

Layer Thickness

~1.0–1.3 mm in 2 coats

Ambient Air Temperature

+10 °C min. / +40 °C max.

Substrate Temperature

+10 °C min. / +40 °C max.

Pot Life

~45 minutes (100 g mass, +27 °C)

Waiting Time / Overcoating

Note: Above values are at +30 °C and 50% relative humidity. Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.

Applied Product Ready for Use

IMPORTANT

Applied SikaTop®-107 Seal Plus IN must not be subjected to ponding before 7 days. Contact Sika Technical Services and refer to ASTM D5957 for more information.

0.6 to 0.75 m² per kg

Note: The consumption will vary depending on application area, substrate type, substrate roughness, surface profile, absorption of the surface, and thickness required.

EQUIPMENT
Mixing
Electric drill paddle mixer (>700 W, 300 to 500 rpm)
Application
Hard bristled brush
Squeegee
Flat trowel
MIXING
IMPORTANT

Do not add water in any circumstances.

IMPORTANT

For bigger pack, mix only the quantity which can be used within the pot life.

Waterproofing Coating
Pour full quantity of SikaTop®-107 Seal Plus IN Part A into a clean mixing container.
While stirring slowly, add SikaTop®-107 Seal Plus IN Part B.
Mix thoroughly for 3 minutes, until free from lumps and smooth consistency is achieved.
Waterproofing Mortar
Pour 90% of SikaTop®-107 Seal Plus IN Part A into a clean mixing container.
While stirring slowly, add SikaTop®-107 Seal Plus IN Part B.
Mix thoroughly for 3 minutes, until free from lumps and smooth consistency is achieved.
APPLICATION
IMPORTANT

SikaTop®-107 Seal Plus IN may display signs of “blooming” after rain or in damp weather. This does not affect the performance of the coating in any way.

IMPORTANT

Do not apply in direct sun and/or strong wind.

IMPORTANT

In areas of severe water penetration, three coats might be required.

IMPORTANT

Protect freshly applied material from freezing conditions, rains etc.

Detailing
Seal all penetrations with a suitable Sika sealant like SikaSwell® S-2 or Sikagard® 694 F(I) epoxy putty to prevent any leakage from the periphery of the down take pipes.
Additionally, if so desired cut Sika® Fabric-50 to desired dimensions for detailing on intersections and also around pipe penetration by embedding it with the SikaTop®-107 Seal Plus IN.
Sika® SealTape F is recommended to be used as a component of a composite sealing system in conjunction with SikaCeram® tile adhesive and ceramic tiles to achieve water tightness in wet rooms and around wet areas.
Waterproofing Coating
Thoroughly pre-wet the prepared substrate (2 hours recommended) before application. Keep the surface wet and do not allow to dry. Before application remove excess water, e.g. with a clean sponge. The surface must appear a dark matt appearance without shining and surface pores and cavities must not contain water.
Apply the first coat of SikaTop®-107 Seal Plus IN with a hard bristled brush or broom applied in the same direction and leave to harden for 2 to 6 hours.
(Optional) Wherever coating is to be reinforced with glass fabric, lay Sika® Fabric-50 into the freshly applied base coat and embed firmly into the wet coat with brush.
Apply the second coat of SikaTop®-107 Seal Plus IN in crosswise direction to the first application as soon as the first coat has hardened.
Waterproofing Mortar
Thoroughly pre-wet the prepared substrate (2 hours recommended) before application. Keep the surface wet and do not allow to dry. Before application remove excess water, e.g. with a clean sponge. The surface must appear a dark matt appearance without shining and surface pores and cavities must not contain water.
Apply the first coat of SikaTop®-107 Seal Plus IN by a flat trowel applied in the same direction and leave to harden for 2 to 6 hours. For pore / blowhole filling, tightly trowel into the pores / blowholes of the surface.
(Optional) Wherever coating is to be reinforced with glass fabric, lay Sika® Fabric-50 into the freshly applied base coat and embed firmly into the wet coat with trowel.
Apply the second coat of SikaTop®-107 Seal Plus IN in crosswise direction to the first application as soon as the first coat has hardened.

Note: If the second coat is applied 12 hours or later to the first coat, the first coat shall be slightly pre-wetted by using a fine spray.

IMPORTANT

Slight fabric marks may be visible after application of the second coat, but it will have no adverse bearing on the performance of the waterproofing system.

Protection
The top coat while wet, sprinkle clean quartz sand.
Once the top coat has sufficiently cured, apply protection plaster, mortar, screed or any other adhesive layer. A bonding agent may be necessary.
Alternatively, a separation layer like PE sheet or geotextile can be used before any plaster / screed / interlocking paver blocks.
CURING TREATMENT

Cure SikaTop®-107 Seal Plus IN for minimum 7 days to ensure full cement hydration and minimise cracks. Use wet hessian cloth, spray curing or similar approved methods during the recommended period of curing.

CLEANING OF TOOLS

Clean all tools and application equipment with water immediately after use. Hardened material can only be removed mechanically.